[Boards: 3 / a / aco / adv / an / asp / b / bant / biz / c / can / cgl / ck / cm / co / cock / d / diy / e / fa / fap / fit / fitlit / g / gd / gif / h / hc / his / hm / hr / i / ic / int / jp / k / lgbt / lit / m / mlp / mlpol / mo / mtv / mu / n / news / o / out / outsoc / p / po / pol / qa / qst / r / r9k / s / s4s / sci / soc / sp / spa / t / tg / toy / trash / trv / tv / u / v / vg / vint / vip / vp / vr / w / wg / wsg / wsr / x / y ] [Search | Free Show | Home]

Is there a type of power inverter that is auto on/off? I would

This is a blue board which means that it's for everybody (Safe For Work content only). If you see any adult content, please report it.

Thread replies: 11
Thread images: 1

Is there a type of power inverter that is auto on/off? I would like to wire something up permeantly so I don't have to keep plugging it in and out.
>>
>>16875357
Just put it on a ACC wire.
>>
cut the hot wire and place a switch on it
>>
>>16875362
But then it will run whenever the car is on. And I have a newer Ford escape and they don't really have the traditional ACC wire. I know because I installed a dash cam and looked for the ACC wire
>>
>>16875389
Then put it on a toggle.
>>
>>16875396
I want it automatic like my Impala. It automatic turns on when you plug something in
>>
>>16875489
Then you have to buy an inverter that has that feature
>>
>>16875506
I can't find any anywhere? What's that feature called?
>>
>>16875389
Find an accessory (like the stereo) and splice into the switch wire that actuates it. Take it to the trigger input on a relay that's big enough to run the amperage the inverter requires. Done.
>>
>>16875510
probably like load sensing or just auto on
>>
>>16875357
This might be a little to advanced for a total rookie in electronics but you can make it turn on or off using the ignition signal with an N-channel MOSFET.

Cut in half the negative cable of the inverter that goes in the cigarette ligheter and solder the MOSFET drain pin to the bit going off the inverter and source pin to the other bit going to GND. Do some wiring and connect the ignition signal to the gate and voilĂ !

Make sure you use a power-MOSFET and well insulate-case everything.

Pro-tip: put some very high resistance (1Mohm) across the gate and source to allow the gate to discharge faster.

Pro-pro-tip: learn some electronics
Thread posts: 11
Thread images: 1


[Boards: 3 / a / aco / adv / an / asp / b / bant / biz / c / can / cgl / ck / cm / co / cock / d / diy / e / fa / fap / fit / fitlit / g / gd / gif / h / hc / his / hm / hr / i / ic / int / jp / k / lgbt / lit / m / mlp / mlpol / mo / mtv / mu / n / news / o / out / outsoc / p / po / pol / qa / qst / r / r9k / s / s4s / sci / soc / sp / spa / t / tg / toy / trash / trv / tv / u / v / vg / vint / vip / vp / vr / w / wg / wsg / wsr / x / y] [Search | Top | Home]

I'm aware that Imgur.com will stop allowing adult images since 15th of May. I'm taking actions to backup as much data as possible.
Read more on this topic here - https://archived.moe/talk/thread/1694/


If you need a post removed click on it's [Report] button and follow the instruction.
DMCA Content Takedown via dmca.com
All images are hosted on imgur.com.
If you like this website please support us by donating with Bitcoins at 16mKtbZiwW52BLkibtCr8jUg2KVUMTxVQ5
All trademarks and copyrights on this page are owned by their respective parties.
Images uploaded are the responsibility of the Poster. Comments are owned by the Poster.
This is a 4chan archive - all of the content originated from that site.
This means that RandomArchive shows their content, archived.
If you need information for a Poster - contact them.